studiospot.blogg.se

Carrier command 2 manual
Carrier command 2 manual









carrier command 2 manual
  1. #Carrier command 2 manual full#
  2. #Carrier command 2 manual password#
  3. #Carrier command 2 manual mac#

It is suggested to create additional connection from the LTE router to the host for configuration purposes. Note, that it will not be possible to connect to the LTE router via public lte ip address or from the host which is used by the passthrough.

carrier command 2 manual

On the host on the network where the Passthrough is providing the IP a DHCP-Client should be enabled on that interface to. If there are multiple hosts on the network it is possible to lock the Passthrough to a specific MAC.

#Carrier command 2 manual mac#

Router will automatically detect MAC address of the first received packet and use it for the Passthrough. Some modems support multiple APN where you can pass the traffic from each APN to a specific router interface. The LTE Passthrough modem can pass both IPv4 and IPv6 addresses if that is supported by modem. In this configuration the router will not get IP configuration from the modem. In this case modem firmware is responsible for the IP configuration and router is used only to configure modem settings - APN, Network Technologies and IP-Type. Starting from RouterOS v6.41 some LTE interfaces support LTE Passthrough feature where the IP configuration is applied directly to the client device. Manufacturer: Huawei Technologies Co., Ltd. If required, add NAT Masquerade for LTE Interface to get internet to the local network:Īdd action=masquerade chain=srcnat out-interface=lte1Īfter interface is added, you can use "info" command to see what parameters client acquired (parameters returned depends on LTE hardware > /interface lte info lte1 once If it's not added - add a DHCP Client to LTE Interface manually:Īdd default-route-distance=1 disabled=no interface=lte1 LTE interface should appear with running (R) > /interface lte printĠ R name="lte1" mtu=1500 mac-address=AA:AA:AA:AA:AA:AAįrom RouterOS=>6.41 DHCP client is added automatically. Select newly created profile for LTE connection: Warning: This guide is for RouterOS versions starting from 6.41Īdd new connection parameters under LTE apn profile (provided by network provider):Īdd name=profile1 apn= authentication=chap password=web user=web You can also use "at-chat" function in scripts and assign command output to > :global "lte_command" [/interface lte at-chat lte1 input="AT*mrd_imei\?" as-value > :put $"lte_command" It is possible to send user defined "at-chat" command to LTE interface with /interface lte at-chat > /interface lte at-chat lte1 input="AT*mrd_imei\?" Send a command to LTE card to extract useful information, e.g. It is possible to send special "info" command to LTE interface with /interface lte info command. It is possible to scan LTE interfaces with /interface lte scan command Username used if any of the authentication protocols are active If set to yes, uses DNS recieved from LTE interface

#Carrier command 2 manual password#

Password used if any of the authentication protocols are active If set to auto, then will learn MAC from first packet Interface to passthrough IP configuration (activates passthrough) Interface on which to advertise IPv6 prefix Ip-type ( ipv4 | ipv4-ipv6 | ipv6 Default: ) LTE route by default is with distance 2 to prefer wired routes over LTE Sets distance value applied to auto created default route, if add-default-route is also selected. Whether to add default route to forward all traffic over the LTE interface.Īuthentication ( pap | chap | none Default: none)Īllowed protocol to use for authenticationĭefault-route-distance ( integer Default: 2)

carrier command 2 manual

PLMN codesĪll network related settings are moved under profiles, starting from RouterOS 6.41

#Carrier command 2 manual full#

Used to lock device to specific operator full PLMN number is used for lock consisting from MCC+MNC.

carrier command 2 manual

Select/force mode for LTE interface to operate with Network-mode ( 3g | gsm | lte Default: 3g,gsm,lte) Max packet size that LTE interface will be able to send without packet fragmentation. Modem init string (AT command that will be executed at modem startup) Media Access Control number of an interface. Which APN profile to use for this interfaceįrequency band used in communication LTE Bands and bandwidths Some modems, that do not fully support this feature, will connect to the network but will not establish an IP data connection with allow-roaming set to no. Sub-menu: /interface lte Properties PropertyĮnable data roaming for connecting to other countries data-providers. Warning: In RouterOS v7 ignore-direct-modem parameter is moved under /system routerboard modem menu











Carrier command 2 manual